Victron Phoenix Smart IP43 3 Output 12V Charger 30A

Victron Phoenix Smart IP43 3 Output 12V Charger 30A

Based on 0 reviews. - Write a review

£83.80

Qty

Add to Cart

Buy Now Question

Add to Wish List

Description

Voltage: 12V
Charge Current: 30A
Input Voltage: 230V
Number of Outputs: 3
Protection Category: IP43 (electronic components) IP22 (connection area)
Efficiency: 94%
Bluetooth Enabled: Yes
Dimensions: 180 x 249 x 100mm
Weight: 3.5Kg
Warranty: 5 Years

<a class=\"pagebuilder-button-primary\" href=\"https://www.victronenergy.com/upload/documents/Datasheet-Phoenix-Smart-IP43-Charger-230V-EN.pdf\" target=\"_blank\" style=\"text-align: center; font-weight: normal;\"> Datasheet </a> <a class=\"pagebuilder-button-primary\" href=\"https://www.victronenergy.com/upload/documents/Phoenix_Smart_IP43_Charger_230V/Phoenix_Smart_IP43_Charger-en.pdf\" target=\"_blank\" style=\"text-align: center; font-weight: normal;\"> Manual </a>

With boat owners in mind this adaptive 5-step charger can provide either 30A or 50A of charge to each of three battery banks. With Bluetooth enabled it is posible to monitor the charger and set alarms straight from a connected phone.

Features

Bluetooth Smart enabled

Any Bluetooth enabled smart phone tablet or other device can be used to monitor to change settings and to update the charger when new software features become available.

Phoenix Smart (3): three full current outputs to charge 3 battery banks

Each output can supply the full rated output current. But the total of the 3 outputs combined can never exceed the current rating of the charger

Automatic voltage compensation

The charger compensates for voltage drop over the DC cabling by slightly increasing output voltage when the DC current increases. Please see the manual for details.

Adaptive 5-stage charge algorithm: Bulk – Absorption – Recondition – Float – Storage

The Phoenix Smart Charger features our well-known ‘adaptive’ battery management system that can be preset to suit different types of batteries. The ‘adaptive’ feature will automatically optimise the charge process relative to the way the battery is being used.

The right amount of charge: variable absorption time

When only shallow discharges occur (a yacht connected to shore power for example) the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery will be fully charged.

Preventing damage due to excessive gassing: the BatterySafe mode

If in order to quickly charge a battery a high charge current in combination with a high absorption voltage has been chosen the charger will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached

Less maintenance and aging when the battery is not in use: the Storage Mode

The Storage Mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the Storage Mode float voltage is reduced to 2 2 V/cell (13 2 V for a 12 V battery) to minimise gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the electrolyte and sulphation a major cause of early battery failure.

Also charges Li-ion (LiFePO₄) batteries

Charger on-off control can be implemented by connecting a relay or open collector optocoupler output from a Li-ion BMS to the remote on-off port. Alternatively full control of voltage and current can be achieved with Bluetooth.

Fully programmable charge algorithm

The charge algorithm can be programmed with help of Bluetooth or the VE.Direct interface. Three preprogrammed algorithms can be selected with the mode button (see specifications).

Remote on-off

The remote on/off consists of two terminals: Remote H and Remote L. A remote on/off switch or relay contact can be connected between H and L. Alternatively terminal H can be pulled high or terminal L can be pulled low. See manual for details.

VE.Direct interface

For a wired data connection to a Color Control panel PC or other devices. Please see the VictronConnect app under Downloads / Software on our website.

Programmable relay

Can be programmed using the VE.Direct interface or a Bluetooth enabled device to trip on an alarm or other events.